Parallel Data Cable (Printer extension cable, with male-female 25 pin connector, and pin to pin through)	A-A type USB cable(for power)



ATMEL89 Adapter	ATMEL PLCC 44 Adapter	TSOP 48 Adapter

FWH/HUB PLCC32Adapter	PLCC32 Adapter	SOIC Adapter(Simplified)
On-Board	On-Board
AC or DC Power Adapter (9V or 12V, 200mA)	SOIC Adapter(Professional)	
		

Tarea 1041.zip Instant

If you can provide more context on the (e.g., is it engineering, literature, etc.) or what institution provided it, I may be able to find more specific information.

If "solid paper" was intended to be "solid soil" or related to structural integrity, research often focuses on low-volume roads and road drainage . Tarea 1041.zip

Note: The search results do not contain the specific file or content for "Tarea 1041.zip". If you can provide more context on the (e

Based on the request, "Tarea 1041.zip" appears to be a specific project or assignment file, potentially related to soil mechanics or a solid-state topic, but there are no direct matches for this specific filename in the provided search results. Based on the request, "Tarea 1041

"Hardback/alkaline paper" is mentioned in a catalog concerning social movements in developing countries.

However, related to the query "solid paper" and potential interpretations, here is some relevant information found:

Installation Steps


Check the parallel printer port setting in the bios, it should be EPP or Normal.
Check there are any active resident programs that use the printer port, such as TWAIN drivers. You may have to remove it.
Connect one end of the 25 pin SubD parallel cable to PCprinter port
Connect the other end of parallel cable to 25Pins port of the programmer
Connect USB power cable or AC adaptor (Note: if you are working on the EPROM programming. You may need use a AC adaptor, so that you can get Vcc 5.6V and 6.2V when doing programming)
Theyellowpower normal indicator of the programmer should light up, then the programmer power supply is normal.
Run the software
Select devices type
Click the Willem in toolbar to change to PCB3
Set the DIP switch based on the displayed pattern.

 (Note: theLPT portof PC MUSTset to ECP or ECP+EPP during BIOS setup. To enter the BIOS setting mode, you need press "Del" key or "F1" key during the computer selftest, which is the moment of computer just power up.)



Software Version To Use

The softwarecan be download fromdownload.mcumall.com

There are board hardware selection jumper on the board. When set the jumper to PCB3B, then user have to use 0.97ja and before version software.

If the board selection set to PCB3.5, PCB5.0, PCB5.5C, then the software 0.98D6 should be used.



 The softwareinterface:



Tarea 1041.zip



Hardware Check

After start the program, click test hardwar under Help menu. If the connection and power supply is normal, then appears: "Hardware present" Otherwisecheck if the programmer connects well with PC, or power supply is normal.



Jumper Configuration



PCB3.5/PCB4E

Tarea 1041.zip 
(Two PLCC32 adapter is not applied on the PCB4E)



PCB5.0

Tarea 1041.zip



PCB5.5C



Tarea 1041.zip

Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. For the USB power only 5V Vcc is available.

For the PCB5.5C, set DIP steps:

1. press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

2. press DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

3. Repeat those steps till all DIP bit ae set same as software indicated.

For PCB5.5C voltage and Special chip selection:

1. Put back the safety jumper.

2. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up.

3. Press the chip selectionbutton and hold for 1 second, the chip LED should move to next. Repeat till desiredLED light up.

4. Remove the safety jumper to lock the selected voltage and chip selection



DIPSwitch (PCB3.5, PCB5.0)

Tarea 1041.zip 

When programming one chip, followthe program prompt to set DIP switch.



If you can provide more context on the (e.g., is it engineering, literature, etc.) or what institution provided it, I may be able to find more specific information.

If "solid paper" was intended to be "solid soil" or related to structural integrity, research often focuses on low-volume roads and road drainage .

Note: The search results do not contain the specific file or content for "Tarea 1041.zip".

"Hardback/alkaline paper" is mentioned in a catalog concerning social movements in developing countries.

However, related to the query "solid paper" and potential interpretations, here is some relevant information found: